Enerpac WST-72 Manuale Utente Scaricare il pdf

L2110 Rev. B 01/98

IMPORTANT RECEIVING INSTRUCTIONS

Visually inspect all components for shipping damage. If any shipping damage is found,

notify carrier at once. Shipping damage is NOT covered by warranty. The carrier is

responsible for all repair or replacement cost resulting from damage in shipment.

SAFETY INFORMATION

To avoid personal injury or property damage during system operation, read and follow

all CAUTIONS, WARNINGS, and INSTRUCTIONS, included with or attached to each

product. ENPERPAC CANNOT BE RESPONSIBLE FOR DAMAGE OR INJURY

RESULTING FROM UNSAFE USE OF PRODUCT, LACK OF MAINTENANCE, OR

INCORRECT PRODUCT AND SYSTEM APPLICATION. Contact Enerpac when in

doubt as to safety precautions or applications.

WARNING

Always wear proper personal protective gear when operating hydraulic equipment

(i.e. safety glasses, gloves, etc.).

= WARNING

The system operating pressure must not exceed the pressure rating of the lowest

rated component in the system.

= WARNING

Make sure that all system components are protected from external sources of

damage, such as excessive heat, flame, moving machine parts, sharp edges, and

corrosive chemicals.

= WARNING

Do not exceed the specified maximum load on the support plunger.

=CAUTION

AVOID DAMAGING HYDRAULIC HOSES.

– Avoid sharp bends and kinks when routing hydraulic

hoses. Using a bent or kinked hose will cause severe

back–pressure. Also, sharp bends and kinks will

internally damage the hose leading to premature failure.

–Do not drop heavy objects on hose. A sharp impact may

cause internal damage to hose wire strands. Applying

pressure to a damaged hose may cause it to rupture.

TO PROTECT YOUR WARRANTY, USE ONLY ENERPAC HYDRAULIC OIL.

Instruction Sheet

Fluid Advanced and

Spring Advanced Worksupports

1 2 3 4 5 6 ... 47 48

Sommario

Pagina 1 - Spring Advanced Worksupports

L2110 Rev. B 01/98IMPORTANT RECEIVING INSTRUCTIONSVisually inspect all components for shipping damage. If any shipping damage is found,notify carrie

Pagina 2

ABMESSUNGENMODELL NR. ABCDEFGHWFT71WST7189,2(3.51)79,5(3.13)#2 SAE.312-24 UNF8,6(.34)41,9(1.65)9,7(.38)67,8(2.67)74,9(2.95)WFT72WST72.125 - 28BSPPMODE

Pagina 3 - MODEL NO. P Q R S

ABQRSHPJILMNAbbildung 2 - WFM/WSM-ModelleMODELL NR. A B H I J L M NWFM/WSM 7176,2(3.00)66,5(2.62)62,0(2.44)4,6(.18)15,01(.591)9,7(.38)23,9(.94)M10 X 1

Pagina 4 - SPECIFICATIONS

TECHNISCHE DATENWFT 71, WFT72, WFM 71, WFM 72WST 71, WST 72, WSM 71, WSM 72DRUCK-BEREICH50-350 bar(700-5000) psiHUBmm (in.)9,7(.38) ZYLINDER-KRAFT kN

Pagina 5

070140210280350 1,11 (250)2,22 (500)3,34 (750) 4,45 (1000) 5,56 (1250) 6,67 (1500) 7,78 (1750)(1000)(2000)(3000)(4000)(5000)04,45(1000)0,02 (.001)0,0

Pagina 6 - OPERATION

BESCHREIBUNGHydraulisch anstellbare AbstützzylinderHydrauliköl fließt durch den Ölanschluß und fährt den Kolben aus. Wenn derAbstützzylinder unter Hyd

Pagina 7 - TROUBLESHOOTING

4. Sobald die Bearbeitung beendet ist, die Spannzylinder einfahren und denHydraulikdruck ablassen, indem die Ventile geschlossen werden oder die Pumpe

Pagina 8

Pagina 9 - Hydraulisch anstellbare und

L2110 Rév. B 01/98INSTRUCTIONS IMPORTANTES POUR LA RÉCEPTIONInspecter visuellement toutes les pièces pour détecter les dégâts éventuels subis pe

Pagina 10 - ABMESSUNGEN

NABCDEFGHIJKOPMLDIMENSIONSN° DEMODÈLEABCDEFGHWFT71WST7189,2(3.51)79,5(3.13)#2 SAE.312-24 UNF8,6(.34)41,9(1.65)9,7(.38)67,8(2.67)74,9(2.95)WFT72WST72.1

Pagina 11 - MODELL NR. P Q R S

ABQRSHPJILMNFigure 2 -- Modèles WFM/WSM N° DEMODÈLEABH I J LMNWFM/WSM 7176,2(3.00)66,5(2.62)62,0(2.44)4,6(.18)15,01(.591)9,7(.38)23,9(.94)M10 X 1,56HW

Pagina 12 - TECHNISCHE DATEN

NABCDEFGHIJKOPMLFigure 1 -- WST/WFT ModelsDIMENSIONSMODEL NO. ABCDEFGHWFT71 WST713.51(89,2)3.13(79,5)#2 SAE.312-24 UNF.34(8,6)1.65(41,9).38(9,7)2.67(6

Pagina 13

CARACTÉRISTIQUESWFT 71, WFT 72,WFM 71, WFM 72WST 71, WST 72,WSM 71, WSM 72PLAGE DEPRESSION50-350 bar(700-5000) psiCOURSEmm (in.)9,7(.38) CAPACITÉ À LA

Pagina 14 - BESCHREIBUNG

070140210280350 1,11 (250)2,22 (500)3,34 (750) 4,45 (1000) 5,56 (1250) 6,67 (1500) 7,78 (1750)(1000)(2000)(3000)(4000)(5000)04,45(1000)0,02 (.001)0,0

Pagina 15 - FEHLERTABELLE

DESCRIPTIONExtension par fluideL’huile hydraulique entre par l’orifice et soulève le piston. La tige du vérin est soulevéepar la force du ressort jusq

Pagina 16

ENTRETIEN ET RÉPARATIONIl est nécessaire d’effectuer l’entretien au moindre signe d’usure et/ou de fuite. Inspecterde temps à l’autre tous les composa

Pagina 17 - Notice d’emploi

Pagina 18 - DIMENSIONS

L2110 Rev. B 01/98INSTRUCCIONES IMPORTANTES PARA LA RECEPCIONInspeccione visualmente todos los componentes para ver si han sufrido daños durant

Pagina 19

NABCDEFGHIJKOPMLDIMENSIONESNO. DEMODELO ABCDEFGHWFT71WST7189,2(3.51)79,5(3.13)#2 SAE.312-24 UNF8,6(.34)41,9(1.65)9,7(.38)67,8(2.67)74,9(2.95)WFT72WST7

Pagina 20 - CARACTÉRISTIQUES

ABQRSHPJILMNFigura 2 -- Modelos WFM/WSMNO. DEMODELO A B H I J L M NWFM/WSM 7176,2(3.00)66,5(2.62)62,0(2.44)4,6(.18)15,01(.591)9,7(.38)23,9(.94)M10 X 1

Pagina 21

ESPECIFICACIONESWFT 71, WFT 72WFM 71, WFM 72WST 71, WST 72,WSM 71, WSM 72REGIMEN DEPRESION50-350 bar(700-5000) psiCARRERAmm (pulg)9,7(.38) CAPACIDAD

Pagina 22 - FONCTIONNEMENT

070140210280350 1,11 (250)2,22 (500)3,34 (750) 4,45 (1000) 5,56 (1250) 6,67 (1500) 7,78 (1750)(1000)(2000)(3000)(4000)(5000)04,45(1000)0,02 (.001)0,0

Pagina 23 - DÉPANNAGE

ABQRSHPJILMNFigure 2 -- WFM/WSM ModelsMODEL NO. A B H I J L M NWFM/WSM 713.00(76,2)2.62(66,5)2.44(62,0).18(4,6).591(15,01).38(9,7).94(23,9)M10 X1,5 6H

Pagina 24

DESCRIPCIONAvance hidráulicoEl aceite hidráulico entra por la lumbrera y eleva el pistón. El pistón se eleva por fuerzade resorte hasta que toque la p

Pagina 25 - Hoja de instrucciones

MANTENIMIENTO Y SERVICIOSerá necesario hacer trabajos de mantenimiento cuando se note algún desgaste y/o fuga.Inspeccione ocasionalmente todos los com

Pagina 26 - DIMENSIONES

Pagina 27

L2110 Rev. B 01/98IMPORTANTI ISTRUZIONI AL RICEVIMENTOIspezionare visivamente tutti i componenti per accertare eventuali danni derivanti daltra

Pagina 28 - ESPECIFICACIONES

NABCDEFGHIJKOPMLDIMENSIONIN.MODELLO ABCDEFGHWFT71WST7189,2(3.51)79,5(3.13)#2 SAE.312-24 UNF8,6(.34)41,9(1.65)9,7(.38)67,8(2.67)74,9(2.95)WFT72WST72.12

Pagina 29

ABQRSHPJILMNFigura 2 -- Modelli WFM/WSMN.MODELLO A B H I J L M NWFM/WSM 7176,2(3.00)66,5(2.62)62,0(2.44)4,6(.18)15,01(.591)9,7(.38)23,9(.94)M10 X1,5 6

Pagina 30 - FUNCIONAMIENTO

DATI TECNICIWFT 71, WFT 72,WFM 71, WFM 72WST 71, WST 72,WSM 71, WSM 72CAMPO DIPRESSIONI50-350 bar(700-5000) psiCORSAmm (in.)9,7(.38) FORZASVILUPPATA

Pagina 31 - LOCALIZACION DE AVERIAS

070140210280350 1,11 (250)2,22 (500)3,34 (750) 4,45 (1000) 5,56 (1250) 6,67 (1500) 7,78 (1750)(1000)(2000)(3000)(4000)(5000)04,45(1000)0,02 (.001)0,0

Pagina 32

DESCRIZIONEAzionamento a fluidoL’olio idraulico entra dalla bocca e solleva lo stantuffo che, per sollecitazione elastica, sisolleva finché non entra

Pagina 33 - Manuale di istruzioni

MANUTENZIONE ED ASSISTENZAOgniqualvolta sono presenti usura e/o perdite, è necessario effettuare la manutenzione.Ispezionare di tanto in tanto tutti i

Pagina 34 - DIMENSIONI

WFT 71, WFT 72, WFM 71, WFM 72WST 71, WST 72, WSM 71, WSM 72PRESSURERANGE700-5000 psi50-350 barSTROKEin. (mm).38 (9,7) CAPACITY@ MAX PSI lbs. (kN)165

Pagina 35

Pagina 36 - DATI TECNICI

L2110 Rev. B 01/98BELANGRIJKE INSTRUCTIES BIJ ONTVANGSTControleer alle onderdelen op transportschade. Als er sprake is van transportschadewaa

Pagina 37

NABCDEFGHIJKOPMLAFMETINGENMODELNR. ABCDEFGHWFT71WST7189,2(3.51)79,5(3.13)#2 SAE.312-24 UNF8,6(.34)41,9(1.65)9,7(.38)67,8(2.67)74,9(2.95)WFT72WST72.125

Pagina 38 - FUNZIONAMENTO

ABQRSHPJILMNAfbeelding 2 -- modellen WFM/WSMMODELNR. A B H I J L M NWFM/WSM 7176,2(3.00)66,5(2.62)62,0(2.44)4,6(.18)15,01(.591)9,7(.38)23,9(.94)M10 X1

Pagina 39 - RICERCA GUASTI

SPECIFICATIESWFT 71, WFT 72, WFM 71, WFM 72WST 71, WST 72,WSM 71, WSM 72DRUKGEBIED50-350 bar(700-5000) psiSLAGmm (in.)9,7(.38) VERMOGEN bij MAXDRUKkN

Pagina 40

070140210280350 1,11 (250)2,22 (500)3,34 (750) 4,45 (1000) 5,56 (1250) 6,67 (1500) 7,78 (1750)(1000)(2000)(3000)(4000)(5000)04,45(1000)0,02 (.001)0,0

Pagina 41 - Vloeistof-uitgeschoven en

BESCHRIJVINGVloeistof-uitgeschovenHydraulische olie komt de poort binnen en brengt de zuiger omhoog. De plunjer komtomhoog door veerkracht totdat deze

Pagina 42 - AFMETINGEN

3. Klem het werkstuk op zijn plaats om machinale bewerking te vergemakkelijken.4. Maak de klemmen los wanneer de bewerking klaar is, en ontlast vervol

Pagina 43 - MODELNR. P Q R S

AustraliaENERPACApplied Power Australia, Ltd.P.O. Box 261 Regents ParkSydney, N.S.W. 2143Tel: (61) (2) 9743 8988Fax: (61) (2) 9743 8648CISApplied Powe

Pagina 44 - SPECIFICATIES

01000(70)2000(140)3000(210)4000(280)5000(350) 250 (1,11) 500 (2,22)750 (3,34) 1000 (4,45) 1250 (5,56) 1500 (6,67) 1750 (7,78)01000(4,45).001 (0,02)

Pagina 45

DESCRIPTIONFluid AdvancedHydraulic oil enters the port and raises the piston. The plunger raises by spring forceuntil it contacts the workpiece. Once

Pagina 46 - INSTALLATIE

MAINTENANCE AND SERVICEMaintenance is required when wear and/or leakage is noticed. Occasionally inspect allcomponents to detect any problem requirin

Pagina 47 - OPSPOREN VAN STORINGEN

Pagina 48

L2110 Rev. B 01/98WICHTIGE ANWEISUNGEN FÜR DIE EINGANGSKONTROLLEAlle Komponenten auf eventuelle Transportschäden untersuchen. Sollte ein solcherSchad

Modelli collegati WSM-72 | WFT-72 | WFM-72 |

Commenti su questo manuale

Nessun commento

Enerpac WST-72 Manuale Utente

Navigare online o scaricare Manuale Utente per Attrezzi Enerpac WST-72. Enerpac WST-72 User Manual Manuale Utente

Sommario

Modelli collegati WSM-72 | WFT-72 | WFM-72 |

Commenti su questo manuale

Prodotti e manuali riguardandi Attrezzi Enerpac WST-72